E-Z Lok SK31020 Sraigtinis srieginis įdėklų rinkinys, 304 nerūdijantis plienas, sriegio dydis 3/8-24, sumontuotas ilgis 0,750 (10 vnt. pakuotėje)

Brand:E-Z LOK

2.5/5

79.41

E-Z Lok gamina srieginius įdėklus metalui, plastikui ir medienai. Įmonės būstinė yra Gardenoje, Kalifornijoje.

Į KOMPLEKTĄ ĮSKAIČIUOTA – Patogų rinkinį sudaro srieginiai įdėklai metalui, grąžtas, STI čiaupas, srieginio įdėklo montavimo įrankis ir srieginio laužymo įrankiai. NAUDOJIMAS SU PRITAIKYMIS – Metaliniai srieginiai įdėklai skirti naudoti su minkštais metalais: aliuminiu, ketaus, magnio ir kt. NERŪDIJANČIO PLIENO viela – rinkinyje yra nerūdijančio plieno srieginiai įdėklai, kurie yra atsparūs korozijai ir gali atlaikyti iki 800°F temperatūrą. GREITAI PAŽEISTI PAŽEIDUSIUS SIŪLIUS – Greitai pataisykite pažeistus sriegius arba sustiprinkite įsriegtas skyles minkštuose metaluose naudodami šį sraigtinių sriegių taisymo rinkinį.
Brand E-Z LOK
Country of Origin United Kingdom
Fastener Type E
Item model number SK31020
Manufacturer E-Z LOK
Material Stainless Steel
Package Dimensions 8.39 x 4.69 x 1.26 inches; 8.8 Ounces
Size 3/8"-24 Thread Size, 0.750" Installed Length
Thread Size 3/8"-24

2.5

3 Review
5 Star
60
4 Star
0
3 Star
0
2 Star
0
1 Star
40

Parašykite savo atsiliepimą

Jūsų el. paštas nebus paskelbtas. Visi privalomi laukai pažymėti*

Scritto da: Madelyn Chapman
Excellent Product
Worked perfectly - Saved me $1000, since I didn't have to replace the casting The thread that stripped out had a .5 counter-bore 3/8deep. Then the thread went another 1.25 inches. This was perfect, the tap didn't score the bore at all, and I was able to torque the bolt to the required specification. I will definitely use them again when I strip out another thread. Thanks, Sam
Scritto da: Joy Porter
Wrong size tap!
I ASSUMED that everything in the pack was correct, as it listed the tap as 3/8” x 24. I drilled the hole with the 25/64” bit provided and then tapped it with the tap. I then installed the thread coil. However, when I tried to thread the 3/8x24 bolt, it wouldn’t start. I then discovered the reason was the tap was 3/8x16! I couldn’t back the coil back out! My only solution was to try to retap the coil with my own 3/8x24 tap. This required several hours of time and literally destroyed my tap!!!!
Scritto da: Laurie M. Kiser
Best quality thread repair kit
I have done this process 2 or 3 times before with good results. The hardest part of the job is making the hole and tap straight. This kit has the highest quality tools and the new threads are 100 x stronger than original aluminum alloy. Drill bit is extremely sharp. The bit and tap seemed to self level making diy hand tools ok. Both of the repairs I did were perfectly straight in spite of me. The coil did need A LOT OF lubricant to install correctly. I had to use liquid assembly lube to get the coil to seat properly. Spray lube wasn't enough. Not the cheapest kit but totally worth the extra few dollars.

Susiję produktai

hot
3/5

€ 65.27

3/5

€ 65.27

Atraskite mūsų tarptautinį tinklą

Siunčiame į 28 šalis, daugiau nei 200 000 produktų. Sekite naujienas, užsiprenumeruokite naujienlaiškį.

Array