Freud 98-302: 3 dalių durų konstrukcinių antgalių rinkinys, apvalus ir kvadratinis išorinių ir vidinių durų konstrukcijų rinkinys. Apima 99-267 Roundover RandS w 99-518 Cove Raise Panel Maršrutizatorius - 1-3/4 arba 1-3/8 durys

Name: Freud 98-302: 3 dalių durų konstrukcinių antgalių rinkinys, apvalus ir kvadratinis išorinių ir vidinių durų konstrukcijų rinkinys. Apima 99-267 Roundover RandS w 99-518 Cove Raise Panel Maršrutizatorius - 1-3/4 arba 1-3/8 durys
Brand: Freud
SKU: 0008925054306
Price: 480.88 EUR
Availability: InStock

Brand:Freud

3.3/5

€
480.88

PRODUKTO APRAŠYMAS 3 dalių durų konstrukcijų antgalių rinkinys IŠ GAMINTOJO Kitas Freudas pirmiausia! Ši trijų dalių įėjimo ir vidinių durų konstrukcijų frezų sistema suteikia medienos apdirbtojams unikalią sistemą aukštos kokybės durims statyti naudojant jų maršrutizatorius. Šie puikiai suderinti antgaliai yra skirti gaminti 1–3/4 colio storio išorės arba 1–3/8 colio storio. vidinės durys. Unikali konstrukcija leidžia medienos apdirbtojams gaminti bet kokio ilgio kaiščius ypač tvirtoms jungtims. Naudodami šį rinkinį kiekvienas, turintis 1/2 colio įvorę, gali sukurti gražias 1–3/4 arba 1–3/8 colio storio duris, šoninius žibintus ir bet kokio stiliaus ir bet kokio dydžio skersinius. Komplekte yra Freudo 99-267 Roundover Rail ir Stile antgaliai bei Freudo 99-518 Quadra-Cut Cove Raised Panel antgaliai. Visi antgaliai turi 1/2 colio kotelius. Kiekviename rinkinyje yra nemokamas mokomasis DVD ir informacinis plakatas, padėsiantis jums įgyvendinti projektą. Visi frezavimo antgaliai turi Freudo didelio tankio karbidą su titanu, užtikrinantį ilgą tarnavimo laiką, ir „Perma-Shield“ dangą, atsparią karščiui ir dervos susidarymui. Naudokite su ant stalo montuojamais frezais. Norėdami gauti geriausių rezultatų, atlikite du ar daugiau perdavimų.

Suma

Į krepšelį Pirkti dabar

EAN: 0008925054306

Kategorijos Įrankiai ir namų apyvokos reikmenys, Elektriniai ir rankiniai įrankiai, Elektrinių įrankių dalys ir priedai, Rotuoklių dalys ir priedai, Router Bits, Kraštų apdirbimo ir griovelių formavimo antgaliai,

Naudokite ant stalo montuojamuose nešiojamuose maršrutizatoriuose. Apima mokomąjį mini DVD ir informacinį plakatą. Puikiai tinka smulkių kietmedžių ir minkštųjų medžių frezavimui, taip pat puikiai pjauna ir kitas medžiagas. Abiejuose antgaliuose yra tarpikliai, skirti tiksliai sureguliuoti jungtį, kad būtų užtikrintas tobulas tvirtinimas. Specifikacijos: Shank Dia. 1/2.

Batteries Required?	‎No
Brand	Freud
Color	‎Multi
Country of Origin	‎Italy
Customer Reviews	4.3 4.3 out of 5 stars 94 ratings 4.3 out of 5 stars
Finish	‎Titanium
Included Components	‎Door Making Sets Router Bit
Item model number	‎98-302
Item Package Quantity	‎1
Item Weight	1 Pounds
Item Weight	‎1 pounds
Manufacturer	‎Freud
Material	Blend
Material	‎Blend
Measurement System	‎Metric
Part Number	‎98-302
Product Dimensions	‎1 x 1 x 1 inches
Size	One Size
Size	‎One Size
Style	‎Exterior-Interior Door Construction Set. Includes 99-267 Roundover RandS w 99-518 Cove Raise Panel Router Bit- 1-3/4 or 1-3/8 Doors
Usage	‎Professional
Voltage	‎1 Volts
Wattage	‎1 watts

5 Star

4 Star

3 Star

2 Star

1 Star

Parašykite savo atsiliepimą

Jūsų el. paštas nebus paskelbtas. Visi privalomi laukai pažymėti^*

Jūsų įvertinimas

Scritto da: James Karwacki

Finally Got the correct Item this time.

Will be satisfied. Correct part was delivered this time.

Scritto da: Natalie Pilkey

5 featherboards and 8 foot router table

I tried using these bits with my Bosch router table that I bought from Menards. I could probably produce some low quality crown, but I was looking for as close to perfect at possible. I converted some old cabinets to a rolling router table and took all the parts off my Bosch table and produced an 8 foot table so I have plenty of infeed and outfeed. I also built a 9 inch fence with 5 featherboards to stabalize the boards as I run them through my process. I also adhered to freuds instructions which I found very helpful. I think the biggest issue is simply accepting the fact that you need a lengthy infeed and outfeed if you want flawless crown. I do not have to trim ends, it is perfect from end to end. I prefer 4 passes vs 3 passes. I mostly use MDO so I have very consistent results. The cost to produce enough trim for a room is so low. However, I've invested alot of time into my process. I measure everything in 32nds to maintain my quality and only use boards that are exactly 5 1/2 inches, else results are poor. I posted some pics if my results after sanding the line that is produced after routing the upper-profile. I only use Freud bits... Amazing products. I can produce higher quality than anything found in a store... I take pride in the process, it is a highly satisfying addiction:)

Scritto da: Isaac Moore

Nice profile - Setup your table properly

I used these bits to route a profile on a 5" high square base frame for a rotating bookshelf. I started with planed stock in both width and thickness. It was imperative to have stock that was the same width to allow the profiles to line up once the ends were mitred. Before each pass, I adjusted the fence and feather boards. It was very important to use double feather boards on the table and to have two f/b's attached to the table's fence. With this setup, I only had to push the boards from the end...no hand support around the bit. The finished product was very good. I had minor areas where the two bits left a line, but it was easily sanded out, even though I was using curly maple. I did get a little chatter 3-4" on the ends of the boards, but these were offcut when mitreing. BTW, Woodcraft has examples of routed profiles in their stores under the display. That is how I decided on which bit set to choose. Happy routing.

Scritto da: Traci Wills

The price was right

The price is certainly right, and they look very sharp. We purchased these as a gift and the packaging was broken when they arrived which was very disappointing but our son in law thought they did not look used. RELIEF since we bought them for him for Christmas. I will update this when he is able to use them. We offered to return them but he was pretty excited about getting them, especially this brand because it's a brand that retails at a much higher price. I'll add pics soon.

Scritto da: ajb

Hard to get

Freud bits are top of the line. I am replenishing after my shop got robbed and it is very difficult to find router bit sets. So I had to over pay for these but I need them for a project I have to start right away.

Scritto da: Gary

Freud Crown Molding bits

The bits are terrific. The documentation is lacking as well as the poor packaging for shipment. Their light plastic case is good for a store display but is dismal for shipment. Mine arrived with the plastic shattered, luckily the bits were OK. They perform very well and are extremely sharp. They recommend three passes to complete the profie. I chose to do four, with the last at about 0.010" just to polish the mahogany I was milling for a book case project.

Scritto da: Kurt

Great set of bits, poor packaging

I received the bits in a flimsy plastic packaging. Although I haven't got the chance to use them yet, they seem very well engineered and are very sharp. 1 of the bit has gotten some dents on it, they're not too deep and it seems as it happened during shipping. It's a shame that such quality products that you pay top dollar for come in such cheap packaging. As soon as I've used them I will update my review. I'm still hoping the dents won't affect the finishing too much. On documentation, there was a piece of cardboard with the packaging illustrating the type of moldings you can create. As I'm familiar with these bits, that seems sufficient enough for me.

Scritto da: Kindle Customer

Crown moulding router bit set

Although these bits are well made they are too large for my porter cable 1-1/2 hp router to handle. I set one up with the router and router table and tried to run a board through. There was so much vibration that I had to shut it off. I guess I'll be buying a shaper so I can use these.

Scritto da: Mitch Leonard

Works perfectly

Obviously these things rock. Freud makes quality products. Very precise. Comes in cheap plastic. This is really about the router bits

Scritto da: ANA PATRICIA ROBLES LINARES

Excelente compra

Excelente calidad muy recomendable.