PacTool SS724 Snapper Shear Pro - Pjovimo įrankis pluoštinio cemento plokštėms - Elektrinės žirklės Profesionalūs elektriniai įrankiai Universali kirpimo galvutė / Tvirtinama prie bet kokio gręžimo Pjovimo įrankio

Name: PacTool SS724 Snapper Shear Pro - Pjovimo įrankis pluoštinio cemento plokštėms - Elektrinės žirklės Profesionalūs elektriniai įrankiai Universali kirpimo galvutė / Tvirtinama prie bet kokio gręžimo Pjovimo įrankio
Brand: PacTool
SKU: 0645646724004
Price: 117.66 EUR
Availability: InStock

Brand:PacTool

3.5/5

€
117.66

Padarykite kitą statybos darbą lengvesnį ir lengviau valdomą naudodami mūsų novatorišką akumuliatorinį pjovimo įrankį, kuris puikiai tinka bet kokiam komercinių įrankių rinkiniui arba namams. Šis priedas veikia su bet kokiu 18 voltų ar didesnės įtampos akumuliatoriniu gręžtuvu ir jį lengva manevruoti atliekant bet kokį pjūvį. Jis specialiai sukurtas pjauti pluoštinio cemento pagrindo plokštes, tokias kaip „HardieBacker“, ir gali sudaryti tiesius, stačiakampius 90° laipsnių apskritimus ir pjauti net 3 colių skersmens. Mūsų universalus pjovimo įrankis, reguliuojamas ir pritaikomas dešiniarankiams ir kairiarankiams, baigėsi. Šios žirklės turi laisvai besisukančią pasukamąją galvutę, leidžiančią lengvai sekti lentos kelius ir linijas, puikiai tinka namo dailylentėms, pertvarkoms, virtuvės ir vonios renovacijai bei įrengimams. Padarykite, kad jūsų darbo vieta atitiktų OSHA reikalavimus, nes dėl kirpimo praktiškai nėra oro sklindančių dulkių – šis įrankis padaro bet kokį darbą efektyvesnį ir saugesnį visiems darbo vietoje. PacTool esame žinomi dėl išskirtinės išorės gaminių linijos statybos, renovacijos ir pertvarkymo sektoriuje ir didžiuojamės teikdami išskirtinius sprendimus, kurie padeda sumažinti amatininkų, amatininkų ir pasidaryk pats.

Suma

Į krepšelį Pirkti dabar

EAN: 0645646724004

Kategorijos Įrankiai ir namų apyvokos reikmenys, Elektriniai ir rankiniai įrankiai, Elektriniai įrankiai, , Žirklės,

PACTOOL: pasitikime dešimtmečius, esame specializuotų statybos, renovacijos ir pertvarkymo projektų lyderiai. Mūsų patentuota produktų linija įkvepia amatininkus ir pasidaryk pats dirbti išmaniau, geriau matuoti ir efektyviau taisyti. IŠMANIOS ŽIRKLĖS: šis gręžimo priedas sumažina ore sklindančių dulkių kiekį, todėl profesionalai ir „pasidaryk pats“ gali lengvai pjauti ir sumontuoti. Tai žymiai padidina efektyvumą ir apsaugo darbuotojus nuo pavojingų dalelių. DIDĖJIMO ĮRANKIAI: Nebereikia taškų ir spragtelėjimo. Dėl šio įrankio universalumo jis puikiai tinka įvairiems dailylentės pertvarkymo projektams, virtuvės, vonios kambario remontui ir įrengimams, ypač pjovimui už kampo, lizdų, techninės įrangos ir tualeto flanšų. KONTRAKTORIŲ ĮRANKIS: Išpjaukite bet kokią formą naudodami šią universalią kirpimo galvutę, kuri gali suktis 360° kampu. Galite daryti tiesius, stačiu kampu, išlenktus pjūvius ir pjauti iki 3 colių skersmens apskritimus, suteikdami ergonomišką pranašumą prieš tradicines žirkles. GRĄŽIMO PRIEDAS: Ši naujoviška kirpimo priemonė patogiai veikia su bet kokiu 18 voltų ar aukštesnės įtampos akumuliatoriniu grąžtu, todėl pjaunant galite lengvai naršyti priedą. Šis gaminys yra specialiai sukurtas pjauti 1/4–1/2 colio HardieBacker pluoštinio cemento plokštę.

Batteries Required?	‎No
Blade Edge	‎Straight
Brand	PacTool
Brand	‎PacTool
Color	Multi-color
Color	‎Multi-color
Country of Origin	‎USA
Customer Reviews	4.5 4.5 out of 5 stars 1,433 ratings 4.5 out of 5 stars
Finish	‎Powder Coated
Finish Type	‎Powder Coated
Included Components	‎Snapper Shear Pro
Item Dimensions LxWxH	5 x 3.5 x 4 inches
Item Dimensions LxWxH	‎5 x 3.5 x 4 inches
Item model number	‎SS724
Item Package Quantity	‎1
Item Weight	0.01 Ounces
Item Weight	‎0.01 Ounces
Manufacturer	‎General Tools
Part Number	‎SS724
Pattern	‎Cutting Tool
Power Source	‎Hand Powered
Product Dimensions	‎5 x 3.5 x 4 inches
Shape	‎Straight
Style	Universal Shear Head / Attaches to any drill
Style	‎Universal Shear Head / Attaches to any drill
Warranty Description	‎See more details at generaltools.com, 1 Year Limited

5 Star

4 Star

3 Star

2 Star

1 Star

Parašykite savo atsiliepimą

Jūsų el. paštas nebus paskelbtas. Visi privalomi laukai pažymėti^*

Jūsų įvertinimas

Scritto da: Pinser

Cuts 1/2” hardybacker like butter

Tool functions as described by the manufacturer. I used an auto tightening chuck on a big drill motor and it cut 1/2 inch hardybacker like butter and it was very easy to follow a straight line. Recommend a sturdy table to clamp your board down to.

Scritto da: James Meservy

Outstanding tool for cement board

If you’re cutting hardiebacker you need this, glides through like butter and no dust. Was a lifesaver doing my bathroom remodel.

Scritto da: B. King

Excellent cutting tool for Hardi backer board

Take my advice, buy this took if you work with HardiBacker board. I am not a homeowner doing a weekend project. I have tried every possible methods to cut Hardibacker starting with carbide tipped jig saw blades to using a utility knife. I have worked in construction for 45 years and this is one of best tools I have ever used to cut hardibacker. I just finished installing 50 sheets of HardiBacker in a clients home. This tool cuts Hardibacker like a hot knife thru butter. I would also add that the tool is holding up well to all the use, not often do you find a tool that works well and is durable.

Scritto da: Jeff

Not perfect but one of best tools for cutting HardiPlank

The shears worked very well for cutting HardiPlank cement board siding. I used it to crosscut for lengths, as well as ripping lengthwise for width of starter and top course. It is much faster than a jig saw with diamond grit blade. The jigsaw cut super smooth edge but was very slow. These shears cut a slightly rough edge but totally acceptable for the hidden areas. Remember to paint with primer all cut edges. The shears cut about a 1/4” wide strip. Each edge of the cut is 1.5” from the edge of the corresponding sole plate edge guide. I clamped a 7” rafting Square 1.5” shy of the cut line and ran the edge of the shear’s sole plate/shoe along that. It is a bit awkward to try to cut freehand but could be done for all except butted ends For butting to another plank I would try to have both be factory ends, and have the cut on the end by the trim. For cutting lengthwise I placed another plank alongside it, and then stacked four planks on a guideline 1.5” from the cut line. The factory edges have tiny rough spots so be careful as the guide shoe will hang up a bit. Just be patient and smoothly push the shear head along the guide planks. Next time I will use a 2x4 or similar smooth wood cutting guide rather than another plank. It is much easier to handle the planks and set up cutting guides with two people but could be done by a lone worker. I used an older Milwaukee M18 1/2” drill/driver and it had no problem driving the shears. Use the highest drill speed possible. The shears produce virtually no air borne dust. You get some dust on the floor with 1/4” wide curled strips as waste products. Clean up periodically before the curly strips get stepped on and create much more cement dust. The jigsaw created more dust but it was very localized near the saw, unlike how a circular saw throws dust across the entire room. Jigsaw cuts ultra smooth but is very slow, like two minutes to trim length on a 6.26” plank. The shears take about 15 seconds. Bottom line, the shears are the only reasonable way time-wise and with minimal dust to cut HardiPlank. You get acceptable edges in fairly good time and almost no dust in the air. The main downside is they are awkward to control and you should use a firm guide to ensure straight cuts. This shear head is way cheaper than the full tool shears. Plus you get the benefit of working with any corded or cordless drill of 18/20 volts. Be sure to really crank the chuck closed on the head stem as it likes to work itself free. I will always have a jigsaw handy as a backup but these shears are what I will be using for all the siding I am doing in the coming months. Totally worth it! By the way, HardiPlank looks very nice on the house. When we cut ends or edges we just generously coated them with primer and put them up immediately, no waiting for it to fully dry. We even went ahead and primed over every nail head, just in case (I used the pre-primed planks which I think is the easiest version to work with).

Scritto da: Jef Scott

Wish I bought this sooner.

This PacTool Snapper Shear works great. Cuts are quick and easy with minimal clean up so I can actually cut near the installation site instead of going outside. If you’re on the fence about making this purchase I’d recommend getting the shear. Especially if you know you will have future jobs to do.

Scritto da: William Davis ll

Game changer

Chews quickly through backer board.

Scritto da: Phillip R. Andersen Jr.

Best cutter ever

This makes cutting Hardy like cutting thru soft butter. So easy to use and so much faster than any cutting tool out there

Scritto da: Woodys

Impressive

This product was so easy to use! The Snapper Shear literally cuts the concrete board as though it was butter!!

Scritto da: fizzw1

UK plug needed

Great tool but nowhere does it state its a two pin plug you receive so if you were expecting to use it straight away using a 3 pin 240v appliance plug you would be very disappointed. Of little use in the UK originates from the USA.

Scritto da: C-Bass

This is a fantastic tool that works much better than I anticipated. HIGHLY recommended.

I am working on a project that involves cement fiberboard. Having no previous experience with it I quickly realized how much dust was involved cutting with a masonry blade and it would only be realistic to cut outside. But I live in Canada and it's winter so we'll be having none of that. Looking around for other alternatives I came across this tool and was a little hesitant to buy it as this qualifies as "expensive" in my eyes for what it is...a drill attachment. Nevertheless I ordered it and was very curious how well it would perform. It completely blew me away at how easily it cut and created ZERO airborne dust. Much better than I ever expected. If you're thinking about maybe buying this tool...do it. I guarantee you will not regret it.

Scritto da: George Benett

Working flawlessly

Seems like a good investment - works exactly as advertised. Attached to older 18V Makita drill on high speed does flawlessly chew trough those tough 1/2" thick Hardie Backer boards. Used for tight corners, power outlets cutouts, exact cuts using straight edge, cutting circled duct opening and nibbling out just 1/8" along the edge for fine adjustments - no issues. It takes some time to getting used to and to find the right speed, holding angel and amount of push but it shouldn't be a rocket science for anyone, who can at least hold a hammer and drive in a nail. Being able to cut virtually dust free inside is the main bonus I guess. Highly recommended so far. Looks well built and hopefully will last for awhile . . .

Scritto da: Gerry McKinnon

Works great

Works as advertised for casual use. You need to use with a drill Chuck that you can tighten. I tried with an Milwaukee 18 v cordless and it seemed to loosen, but not the fault of the tool. Cuts clean and quick. A little more expensive than a saw blade but no dust and more versatile. Well worth the $$$$

Scritto da: Paul

Works well with a steady hand.

Works well with a steady hand. do a few trial cuts on some waste sections to see how it goes first. Will do a good cut if you keep the tool flat and the boards supported on both ends.