Jutiklio jungiklis MSX12 M4 360 laipsnių kelių tvirtinimo vietų užimtumo jutiklis, baltas

Name: Jutiklio jungiklis MSX12 M4 360 laipsnių kelių tvirtinimo vietų užimtumo jutiklis, baltas
Brand: Sensor Switch
SKU: 0753573998341
Price: 80.41 EUR
Availability: InStock

Brand:Sensor Switch

3.1/5

€
80.41

Reguliuojamas delsos laikas, iš anksto nustatytas iki 15 minučių. Veikia su LED arba fluorescenciniais šviestuvais, juostiniais šviestuvais ir apgaubiančiais šviestuvais. 360 laipsnių pasyvioji infraraudonųjų spindulių technologija užtikrina iki 60 pėdų judesio aptikimą grindų lygyje. Baltas akrilinis korpusas dera su baltos spalvos šviestuvais. Automatiškai įjungia ir išjungia vieną ar kelis įrenginius, kad būtų taupoma ir patogu.

Suma

Į krepšelį Pirkti dabar

EAN: 0753573998341

Kategorijos Įrankiai ir namų apyvokos reikmenys, Elektros instaliacija, Varikliai ir reguliatoriai, Sieniniai jungikliai, Judėjimas- įjungiami jungikliai,

Batteries Included?	‎No
Batteries Required?	‎No
Color	‎White
Country of Origin	‎China
Customer Reviews	4.1 4.1 out of 5 stars 44 ratings 4.1 out of 5 stars
Domestic Shipping	Item can be shipped within U.S.
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer	‎No
Item model number	‎MSX12 M4
Item Package Quantity	‎1
Item Weight	‎5.6 ounces
Manufacturer	‎Sensor Switch
Part Number	‎MSX12 M4
Power Source	‎AC
Product Dimensions	‎4.13 x 4.13 x 2.5 inches
Warranty Description	‎5 years

5 Star

4 Star

3 Star

2 Star

1 Star

Parašykite savo atsiliepimą

Jūsų el. paštas nebus paskelbtas. Visi privalomi laukai pažymėti^*

Jūsų įvertinimas

Scritto da: Jeff Hammer

Wiring not easy

NOTE: If ballast disconnect plugs are cut, white wire with red stripe is Neutral. Cap off plain white wire." I listened to that instruction, capping off the plain white wire (in the set of three). However, the light would not work with that wire out of the equation. I ended up having to wire both the white wire and red-stripe white wire to the ballast's white wire. Then it finally worked! I read in one of the other reviews that someone else had to do this. So beware of this note in the instructions.

Scritto da: Ranger Rick

Seems to work OK. The installation information is OK ...

Seems to work OK. The installation information is OK but the programming instructions are awful. I found these details instructions online. Time Delay Program Instructions 1. Push and hold button until LED flashes rapidly (approximately 6 seconds). Release button. 2. Press button twice to enter Time Delay adjustment mode. The LED will flash back the current Time Delay setting according to below table (i.e. 5 flashes for 10 minute Time Delay). 3. Wait approximately 3 seconds 4. Press button the number of times for the desired setting (i.e., press twice for 2.5 minutes Time Delay). 5. LED will flash back this new setting, (repeated up to 10 times). Press button down again until LED flashes rapidly (approximately 6 seconds). Release button. 6. Press button twice to verify Time Delay has been reprogrammed. LED will flash back twice indicating acceptance of new setting Time Delay Settings Table Push Button the number of increments desired 1 ~ 30 Sec 2 ~ 2.5 Min 3 ~ 5.0 Min 4 ~ 7.5 Min 5 ~ 10.0 Min 6 ~ 12.5 Min 7 ~ 15.0 Min 8 ~ 17.5 Min 9 ~ 20.0 Min

Scritto da: Stan

great motion sensor

Easy to install and program, would buy again. Had it for 5 months and no problems. Installed in our pantry for the light and couldn't be more please,no more pull chain to deal with.

Scritto da: Christy Holter

Works great, very sensitive.

Works great even for a low ceiling but is extremely sensitive.

Scritto da: Anchorman-CET

It has worked for 2+ years

I bought this in October 2018. It has worked flawlessly for all this time. Like so many others my only complaint is the instructions. I shiver with dread anytime I think about changing the shut-off timer. Regardless, it's been very reliable thus far.

Scritto da: William Carson

bettb

This works great. I had to modify the installation because I used it on flush mounted fluorescent lights that could not be accessed from the end where it was intended to be mounted. Mounted it on the inside corner and cut a square out of the lens so the cover can be lowered to replace the bulbs. Works great. The next on I get will be able to install it as intended because they will be surface mounted lights.

Scritto da: Joe Donnelly

Works as advertised

Had my electrician install it. He likes it, I like it. It works great. Going to buy a second one

Scritto da: Amazon Customer

Four Stars

Is working well for fixtures in a shop!